Stamping Disability Analysis on Material SPC 270 E

Article Sidebar

PDF
Published: Apr 26, 2021
DOI: https://doi.org/10.24853/jasat.3.3.75-80
Keywords:
Good quality Process Stamping Testing

Main Article Content

Sri Anastasia Yudistirani
Universitas Muhammadiyah Jakarta
Kisman H. Mahmud
Universitas Muhammadiyah Jakarta
Ery Diniardi
Universitas Muhammadiyah Jakarta

Abstract

Good production results will be a benchmark for a company to compete in today's free market era. To improve good quality is determined by several factors, including: raw material factors, production processes, labor, the state of the engine or dies and the environment. Basically, the production results are not all good, because there are several factors that influence it, as noted above. To overcome this, a company sets a quality requirement because it is very useful for good and quality production results. In determining good quality, it is necessary to conduct a research on the raw material at the SPC 270 E foot step by means of the testing method that will be carried out. The testing methods carried out consist of: tensile testing, hardness testing, metallographic testing, chemical composition testing, and dye penetrant testing. From the results of the research that has been done, it can be seen that the thinning material has an average tensile strength of 307.41 N/mm2, the standard used by the company is 270 - 323 N/mm2 and is still in accordance with the tolerance value. Whereas the material with a lump has an average Vickers hardness value of 124.24 HV, the standard used by the company is 135 HV and still fits the tolerance value.

Article Details

Issue
Vol. 3 No. 3 (2021): Journal of Applied Sciences and Advanced Technology
Section
Articles

COPYRIGHT POLICY

The author(s) of an article published in the Journal of Applied Sciences and Advanced Technology (JASAT) retains ownership of the intellectual property rights in work (s).

PUBLISHING RIGHTS

The author(s) of an article published in the Journal of Applied Sciences and Advanced Technology (JASAT) have unrestricted publication rights. The authors give the Journal of Applied Sciences and Advanced Technology (JASAT) the right to publish the article and designate the Faculty of Engineering Universitas Muhammadiyah Jakarta Publishing as the original publisher of the article.

LICENSING POLICY
JASAT is an open-access journal that follows the Creative Commons Non-Commercial 4.0 International License (CC BY-NC 4.0), which states that: 


Under this license, the reusers must give appropriate credit, provide a link to the license, and indicate if changes were made. Users may do so in any reasonable manner, but not in any way that suggests the licensor endorses users or their use.
Please take the time to read the whole license agreement (https://creativecommons.org/licenses/by-nc/4.0/). As long as reusers follow the license conditions, the owner cannot withdraw these freedoms. The following components are included under this license:

Attribution: Users must provide appropriate attribution, including a link to the license, and indicate whether or not they made any modifications. Users are free to do so reasonably, but not in a manner that indicates the licensee approves of their usage.

NonCommercial: Users may not use the material for commercial purposes.

References

Diniardi, E., Ramadhan, A. I., Mubarok, R., & Basri, H. (2015). Analysis of mechanical properties connecting rod bolts outboard motor FT50CEHD. International Journal of Applied Science and Engineering Research, 4(5), 665-670.

Cooper, D. R., Rossie, K. E., & Gutowski, T. G. (2017). An environmental and cost analysis of stamping sheet metal parts. Journal of Manufacturing Science and Engineering, 139(4).

Park, R. M., Krebs, J. M., & Krebs, F. E. (1996). Occupational disease surveillance using disability insurance at an automotive stamping and assembly complex. Journal of occupational and environmental medicine, 38(11), 1111-1123.

Mahmud, K. H., Yudistirani, S. A., Diniardi, E., & Ramadhan, A. I. (2020). Hardness Analysis of Bearing on Heat Treatment Process. Journal of Applied Sciences and Advanced Technology, 2(3), 59-64.

Yu-ming, Z. H. O. U. (2010). Stamping process for automobile front suspension beam reinforcement with new material. Die and Mould Technology, 2.

Diniardi, E., Nelfiyanti, N., Mahmud, K. H., Basri, H., & Ramadhan, A. I. (2019). Analysis of the Tensile Strength of Composite Material from Fiber Bags. Journal of Applied Sciences and Advanced Technology, 2(2), 39-48.

Rahardja, I. B., Rahdiana, N., Mulyadi, D., Al Afghani, A., & Ramadhan, A. I. (2020). Analisis Pengaruh Radius Bending Pada Proses Bending Menggunakan Pelat Spcc-Sd Terhadap Perubahan Struktur Mikro. Jurnal Teknik Mesin Mechanical Xplore, 1(1), 1-10.

WANG, C. Y., WANG, T. T., & HAN, Y. C. (2008). Research on stamping performance of tailor welded blanks [J]. Forging & Stamping Technology, 4.

Halim, I., Omar, A. R., & Saad, N. H. (2005, June). Investigation Of Work-Related Musculoskeletal Disorders In Malaysian Metal Stamping Industry Using Rula Method. In Paper presented at 8th Conference & Exhibition on Occupational Safety and Health (COSH) (Vol. 28, No. 29).

ZHENG, J. Q., JIANG, X. H., WANG, Y. L., & LI, Z. G. (2005). Research of the CAPP System for the Stamping Process for Auto Body Metal Sheet Parts [J]. Die & Mould Industry, 3.

Othman, N. L. A., Hussain, N. S., Ibrahim, D., & Yaacob, Y. (2019, November). Safety and risk evaluation implementation at sheet metal stamping company using HIRARC model. In IOP Conference Series: Materials Science and Engineering (Vol. 670, No. 1, p. 012070). IOP Publishing.

Ribeiro, I., Peças, P., Silva, A., & Henriques, E. (2008). Life cycle engineering methodology applied to material selection, a fender case study. Journal of Cleaner Production, 16(17), 1887-1899.

Diniardi, E., Setiawan, B., & Ramadhan, A. I. (2019). Fatigue Analysis Aluminium 6063-TF on the Rotary Bending Testing Machine. Journal of Applied Sciences and Advanced Technology, 2(1), 7-12.