PERANCANGAN SISTEM MEKATRONIKA PADA MESIN PEMOTONG RUMPUT MENGGUNAKAN HYBRID ENERGY
DOI:
https://doi.org/10.24853/jurtek.15.1.57-64Keywords:
Hybrid system, power, time, conventional machineryAbstract
This design aims to apply mechatronics technology to a lawn mower. The test includes energy source, transmission capability and comparison of energy consumption with conventional engines This lawn mower design uses a battery with a voltage of 12 volts with a current of 7.2 Ah. The control system is with a frequency of 315 Mhz. Actuators consist of three namely, cutting motor, transmission drive motor and servo motor. Charging the battery uses a hybrid system, namely a solar cell with a capacity of 10 wp and an electric charger of 72 Watts. The engine can operate depending on the power used with a vulnerable time of 50 minutes to 75 minutes per charge. The fastest time when testing at a grass height of 20 mm with a work duration of 6 minutes 15 seconds while the longest time at a grass height of 60 mm for 11 minutes 30 seconds. The charging time of the battery using the longest solar cell on the fourth day for 11 hours and 43 minutes, while the fastest time on the fifth day is during for 6 hours and 42 minutes. For charging using charging a charging time of 1 hour 12 minutes. This machine is more efficient up to 59,000 per month with the same parameters as conventional machinesDownloads
References
Andika, S. (2016). Alat Pemotong Rumput Microcontroller AT Mega 8. Malang: Politeknik Malang.
Bakar, A. (2014). Bahan Ajar Mekatronika. Lhokseumawe: Fakultas Teknik Universitas Malikussaleh.
Groover, M. P. (2009). Fundamentals of Modern Manufacturing 4th. USA: John Wiley&Sons.
Janaloka. (2018). Fungsi Solar Cell pada sistem panel surya. Retrieved Februari 25, 2018, from Janaloka.com:https://janaloka.com/memilih-controller-untuk-sistem-panel-surya
Kho, D. (2018). Pengertian Relay dan Fungsinya. Retrieved Februari 25, 2018, from teknikelektronika.com: https://teknikelektronika.com/pengertian-relay-fungsi-relay/
Paijo. (2007). Pemotong umput. Retrieved Februari 2018, from https://paijo1965.wordpress.com/2007/02/06/pemotong-rumput/
Surhayatun, S. (2002). Mekanisme Pemotong Rumput Dengan Menggunakan Pisau Pemotong Rumput Tipe Rotary. Bogor: Insitut Pertanian Bogor.
Umar. (2016). Perancangan Mesin Listrik Pemotong Rumput dengan Energy Akumulator. Jurnal Teknik Elektro , Vol2 No.2.
Downloads
Published
How to Cite
Issue
Section
License
COPYRIGHT POLICY
The author(s) of an article published in the Jurnal Teknologi retains ownership of the intellectual property rights in work (s).
PUBLISHING RIGHTS
The author(s) of an article published in the Jurnal Teknologi have unrestricted publication rights. The authors give the Jurnal Teknologi the right to publish the article and designate the Faculty of Engineering Universitas Muhammadiyah Jakarta Publishing as the original publisher of the article.
LICENSING POLICY
Journal of Mechanical Engineering and Sciences is an open-access journal that follows the Creative Commons Non-Commercial 4.0 International License (CC BY-NC 4.0), which states that:
Under this license, the reusers must give appropriate credit, provide a link to the license, and indicate if changes were made. Users may do so in any reasonable manner, but not in any way that suggests the licensor endorses users or their use.
Please take the time to read the whole license agreement (https://creativecommons.org/licenses/by-nc/4.0/). As long as reusers follow the license conditions, the owner cannot withdraw these freedoms. The following components are included under this license:
Attribution: Users must provide appropriate attribution, including a link to the license, and indicate whether or not they made any modifications. Users are free to do so reasonably, but not in a manner that indicates the licensee approves of their usage.
NonCommercial: Users may not use the material for commercial purposes.
