IDENTIFICATION OF POTENTIAL HAZARDS ON PRODUCTION MACHINES WITH HAZOPS AND FISHBONE DIAGRAM IN PT. SILINDER KONVERTER INTERNASIONAL

Article Sidebar

PDF
Published: Jun 1, 2021
DOI: https://doi.org/10.24853/sintek.15.1.17-25
Keywords:
Hazard Identification HAZOPS Fishbone Diagrams NGT 5W 1H

Main Article Content

Sofian Bastuti
Pamulang University
Estiningsih TH
Pamulang University

Abstract

PT. Silinder Konverter Internasional is a company in the field of Rotogravure Cylinders. The company is a chemical sector industry and has only been running for about 2 years, for that the company needs to pay attention to the issues of Occupational Safety and Health because this greatly affects the company's productivity. The purpose of this study was to identify the factors causing occupational safety and health hazards to avoid work accidents at PT. Silinder Konverter Internasional. From the results of the research using the Hazards Operability Study (HAZOPS) method, there was 38 potential (40%) chemical potential hazards, 28 potential (29.47%) overwritten materials, 14 potential scratches (14.73%), 12 potential pinches (12.63%), and 3 potential noise levels (3.2%). Furthermore, the causal factors are searched with the fishbone diagram of the most potential hazard cases, namely chemical exposure, there are 12 factors. Followed by finding the dominant causative factors with the Nominal Group Technique (NGT) there are 7 factors. Then plan improvement of the 7 factors with the 5W + 1H method so that the level of risk of work accidents decreases.

Article Details

How to Cite
[1]
S. Bastuti and E. TH, “IDENTIFICATION OF POTENTIAL HAZARDS ON PRODUCTION MACHINES WITH HAZOPS AND FISHBONE DIAGRAM IN PT. SILINDER KONVERTER INTERNASIONAL”, sintek. jurnal. ilm. teknik. mesin, vol. 15, no. 1, pp. 17–25, Jun. 2021.
Issue
Vol. 15 No. 1 (2021): SINTEK JURNAL
Section
Articles

Creative Commons License

  • Articles published in SINTEK JURNAL are licensed under a Creative Commons Attribution-ShareAlike 4.0 International license. You are free to copy, transform, or redistribute articles for any lawful purpose in any medium, provided you give appropriate credit to the original author(s) and SINTEK JURNAL, link to the license, indicate if changes were made, and redistribute any derivative work under the same license.
  • Copyright on articles is retained by the respective author(s), without restrictions. A non-exclusive license is granted to SINTEK JURNAL to publish the article and identify itself as its original publisher, along with the commercial right to include the article in a hardcopy issue for sale to libraries and individuals.

References

R. Bin Nordin, “Rising trend of work-related commuting accidents, deaths, injuries and disabilities in developing countries: A case study of Malaysia,” Ind. Health, vol. 52, no. 4, pp. 275–277, 2014, doi: 10.2486/indhealth.52-275.

F. Ramdan, K. Kunci, I. Bahaya, K. Kerja, and dan Hirarc, “Identifikasi Bahaya Dan Penilaian Risiko Pada Divisi Boiler Menggunakan Metode Hazard Identification Risk Assessment and Risk Control (Hirarc),” J. Ind. Hyg. Occup. Heal., vol. 1, no. 2, 2017, doi: 10.21111/jihoh.v1i1.752.

A. Mansur and M. I. Nasution, “Identification of Behavior Based Safety by Using Traffic Light Analysis to Reduce Accidents,” IOP Conf. Ser. Mater. Sci. Eng., vol. 105, no. 1, 2016, doi: 10.1088/1757-899X/105/1/012033.

Supriyadi, A. Nalhadi, and A. Rizaal, “Identifikasi Bahaya dan Penilaian Risiko K3 Pada Tindakan Perawatan dan Perbaikan Menggunakan Metode HIRARC pada PT. X,” Semin. Nas. Ris. Terap., pp. 281–286, 2015.

R. Alfatiyah, “Analisis Manajemen Risiko Keselamatan dan Kesehatan Kerja dengan Menggunakan Metode HIRARC pada Pekerja Seksi Casting,” J. Mesin Teknol. (SINTEK Jurnal), vol. 11, no. 2, pp. 88–101, 2017.

T. T. P. Rini Alfatiyah, Sofian Bastuti, “Analisis Pengaruh Lingkungan Kerja Serta Jaminan Sosial Terhadap Keselamatan Dan Kesehatan Kerja (K3) Dengan Metode Regresi Linear Berganda Pada Pt. Delta Citra Mandiri,” Pros. Semin. Ilm. Nas. “Membangun Paradig. Kehidup. Melalui Multidisiplin Ilmu,” no. 1, pp. 1–3, 2020.

S. Bastuti, “Analisis Risiko Kecelakaan Kerja Dengan Metode Failure Mode And Effect Analysis (FMEA) Dan Fault Tree Analysis (FTA) Untuk Menurunkan Tingkat Risiko Kecelakaan Kerja (PT. Berkah Mirza Insani) Menurut Departemen Keselamatan dan Kesehatan Kerja DO,” Jitmi, vol. 2, pp. 48–52, 2019.

R. Muhamid, W. Tambunan, and L. D. Fatimahhayati, “Analisis Risiko Keselamatan dan Kesehatan Kerja Kegiatan Bongkar Muat Pupuk,” J. INTECH Tek. Ind. Univ. Serang Raya, vol. 4, no. 2, p. 45, 2018, doi: 10.30656/intech.v4i2.924.

M. Sugarindra, M. R. Suryoputro, and A. T. Novitasari, “Hazard Identification and Risk Assessment of Health and Safety Approach JSA (Job Safety Analysis) in Plantation Company,” IOP Conf. Ser. Mater. Sci. Eng., vol. 215, no. 1, 2017, doi: 10.1088/1757-899X/215/1/012029.

A. C. Ahmad, I. N. M. Zin, M. K. Othman, and N. H. Muhamad, “Hazard Identification, Risk Assessment and Risk Control (HIRARC) Accidents at Power Plant,” MATEC Web Conf., vol. 66, pp. 1–6, 2016, doi: 10.1051/matecconf/20166600105.

R. P. D. S. Restuputri, Dian Palupi, “Analisis Kecelakaan Kerja Dengan Menggunakan Metode Hazard and Operability Study ( Hazop ),” J. Ilm. Tek. Ind., vol. 14, no. 1, pp. 24–35, 2015.

N. A. Siddiquia, N. Abhishek, M. Sharmaa, and A. Srivastava, “Risk Management Techniques HAZOP & HAZID Study,” Occup. Heal. Safety, Fire Environ. – Allied Sci., vol. 1, no. 1, pp. 5–8, 2014.

I. Cameron et al., “Process hazard analysis, hazard identification and scenario definition: Are the conventional tools sufficient, or should and can we do much better?,” Process Saf. Environ. Prot., vol. 110, pp. 53–70, 2017, doi: 10.1016/j.psep.2017.01.025.

C. Carrascosa, R. Millán, P. Saavedra, J. R. Jaber, A. Raposo, and E. Sanjuán, “Identification of the risk factors associated with cheese production to implement the hazard analysis and critical control points (HACCP) system on cheese farms,” J. Dairy Sci., vol. 99, no. 4, pp. 2606–2616, 2016, doi: 10.3168/jds.2015-10301.

S. Bastuti, “Analisis Kegagalan Pada Seksi Marking Untuk Menurunkan Klaim Internal Dengan Mengaplikasikan Metode Plan–Do–Check–Action (PDCA),” J. SINTEK, vol. 11, no. 2, pp. 113–122, 2017.