SINTESIS FASA ɣ-Co PADA PADUAN Co26Cr6Mo0.18N DENGAN KOMBINASI METODE HOMOGENISASI 1200 oC DAN HOT ROLLING SERTA TRANSFORMASI STRUKTUR KRISTALNYA

R. Ibrahim Purawiardi; I Nyoman G. P Astawa; Fendy Rokhmanto; Ika Kartika

SINTESIS FASA ɣ-Co PADA PADUAN Co26Cr6Mo0.18N DENGAN KOMBINASI METODE HOMOGENISASI 1200 oC DAN HOT ROLLING SERTA TRANSFORMASI STRUKTUR KRISTALNYA

R. Ibrahim Purawiardi, I Nyoman G. P Astawa, Fendy Rokhmanto, Ika Kartika

Abstract

Co-Cr-Mo alloy is a material that widely used for bioimplant in the medical field due to its corrosion resistance and mechanical properties. Structurally, recommended Co-Cr-Mo alloys for medical applications are ɣ-Co phase which has an FCC structure. But, Co₇Mo₆ metastable phase often occurs after its synthesis. The formation of Co₇Mo₆ phase will decrease the composition of ɣ-Co phase. This study aimed to synthesize ɣ-Co phase without following the appearance of Co₇Mo₆ phase using a combination of 1200 ^oC homogenization and hot rolling followed by cooling treatment. The alloy used was Co₂₆Cr₆Mo_0.18N ingot. Cooling treatments were done using the variation of cold water, water and air. The transformation of the crystal structure from the primitive cubic to the FCC occurs during water and air cooling treatments which means that ɣ-Co phase is successfully formed by those cooling treatments. However, Co₇Mo₆ phase is still formed on the water cooling treatment while none of Co₇Mo₆occurred on the air cooling treatment. Structurally, air cooling treatment produces most stable ɣ-Co phase than the others. However, brittle ɛ-Co phase as a partial dislocation is formed after air cooling treatment due to imperfection of hot rolling treatment.

Keywords

Co-Cr-Mo alloy; Co26Cr6Mo0.18N ingot; ɣ-Co; homogenization; hot rolling

Full Text:

PDF

References

L. Z. Zhuang, E. W. Langer. “Effects of Alloy Additions on the Microstructures and Tensile Properties of Cast Co-Cr-Mo Alloy Used for Surgical Implants”, Journal of Materilas Science, Vol. 24, pp. 4324-4330, 1989.

J. B. Park. “Microstructure of As-cast Co-Cr-Mo Alloy Prepared by Investment Casting”, Journal of the Korean Physical Society, Vol. 72 (8), pp. 947-951, Apr. 2018.

E. Krasicka-Cydzik, Z. Oksiuta, J. R. Dabrowski. “Corrosion Testing of Sintered Samples Made of the Co-Cr-Mo Alloy for Surgical Applications”, Journal of Materials Science: Materials in Medicine, Vol. 16, pp. 197-202, 2005.

R. Liu, S. Q. Xi, S. Kapoor, X. J. Wu. “Investigation of Solidification Behavior and Associate Microstructures of Co-Cr-W and Co-Cr-Mo Alloy Systems Using DSC Technique”, J. Mater. Sci., Vol. 45, pp. 6225-6234, Jun. 2010.

S. Mineta, Alfirano, S. Namba, T. Yoneda, K. Ueda, T. Narushima. “Phase and Formation/Dissolution of Precipitates in Biomedical Co-Cr-Mo Alloys with Nitrogen Addition”, Metallurgical and Materials Transactions A, Vol. 44A, pp. 494-503, Jan. 2013.

R. K. Shaipov, E. Y. Kerimov, E. M. Slyusarenko. “Phase Equilibria in the Co-Cr-Mo Ternary System at 1375 K with a Cobalt Content Greater Than 50 at.%”, Moscow University Chemistry Bulletin, Vol. 68 (6), pp. 290-292, 2013.

G. E. Kodzhaspirov, M. I. Terent’ev, S. A. Filippov. “Effect of Hot Deformation Parameters on Austenitic Ni-Co-Cr-Mo-Alloy Microstructure Evolution”, Metal Science and Heat Treatment, Vol. 56 (5-6), pp. 239-244, Sep. 2014.

Y. R. Kolobov, S. A. Bozhko, O. A. Golosova, V. N. Sanin, D. M. Ikornikov, V. I. Yukhvid. “Fine-Grained Co-Cr-Mo Alloy by Combined Use of SHS and Thermomechanical Treatment”, International Journal of Self-Propagating High-Temperature Synthesis, Vol. 24 (4), 2015.

C. Suryanarayana, M. G. Norton. X-ray Diffraction: a Practical Approach. Plenum Press, New York, 1998.

J. B. Nelson, D. P. Riley. “An Experimental Investigation of Extrapolation Methods in the Derivation of Accurate Unit-cell Dimensions of Crystals”, Proc. Phys. Soc., Vol. 57 (160), pp. 160-177, Dec. 1944.

A. Lutts. “A New Method for the Determination of Precise Values for the Lattice Parameters from Powder Patterns of Trigonal and Tetragonal Crystals”, Zeitschrift für Kristallographie, Vol. 159, pp. 191-202, 1982.

A. W. Hull. “X-ray Crystal Analysis of Thirteen Common Metals”, Physical Review, Vol. 17, pp. 571-588, May 1921.

K. Rajan. “Nucleation of Recrystallization in a Co-Cr-Mo Alloy”, Metallurgical Transactions A, Vol. 15A, pp. 1335-1338, Jul. 1984.

O. Johnson, R. S. Zhou. “Checking and Estimating RIR Values”, Advances in X-ray Analysis, Vol. 42, pp. 287-296, 2000.

Refbacks

There are currently no refbacks.

SINTEK JURNAL: Jurnal Ilmiah Teknik Mesin Indexed by:

This work is licensed under a by the Creative Commons Attribution-ShareAlike 4.0 International license.

Username
Password
Remember me