Stamping Disability Analysis on Material SPC 270 E

Sri Anastasia Yudistirani, Kisman H. Mahmud, Ery Diniardi

Abstract


Good production results will be a benchmark for a company to compete in today's free market era. To improve good quality is determined by several factors, including: raw material factors, production processes, labor, the state of the engine or dies and the environment. Basically, the production results are not all good, because there are several factors that influence it, as noted above. To overcome this, a company sets a quality requirement because it is very useful for good and quality production results. In determining good quality, it is necessary to conduct a research on the raw material at the SPC 270 E foot step by means of the testing method that will be carried out. The testing methods carried out consist of: tensile testing, hardness testing, metallographic testing, chemical composition testing, and dye penetrant testing. From the results of the research that has been done, it can be seen that the thinning material has an average tensile strength of 307.41 N/mm2, the standard used by the company is 270 - 323 N/mm2 and is still in accordance with the tolerance value. Whereas the material with a lump has an average Vickers hardness value of 124.24 HV, the standard used by the company is 135 HV and still fits the tolerance value.


Keywords


Good quality Process Stamping Testing

Full Text:

PDF

References


Diniardi, E., Ramadhan, A. I., Mubarok, R., & Basri, H. (2015). Analysis of mechanical properties connecting rod bolts outboard motor FT50CEHD. International Journal of Applied Science and Engineering Research, 4(5), 665-670.

Cooper, D. R., Rossie, K. E., & Gutowski, T. G. (2017). An environmental and cost analysis of stamping sheet metal parts. Journal of Manufacturing Science and Engineering, 139(4).

Park, R. M., Krebs, J. M., & Krebs, F. E. (1996). Occupational disease surveillance using disability insurance at an automotive stamping and assembly complex. Journal of occupational and environmental medicine, 38(11), 1111-1123.

Mahmud, K. H., Yudistirani, S. A., Diniardi, E., & Ramadhan, A. I. (2020). Hardness Analysis of Bearing on Heat Treatment Process. Journal of Applied Sciences and Advanced Technology, 2(3), 59-64.

Yu-ming, Z. H. O. U. (2010). Stamping process for automobile front suspension beam reinforcement with new material. Die and Mould Technology, 2.

Diniardi, E., Nelfiyanti, N., Mahmud, K. H., Basri, H., & Ramadhan, A. I. (2019). Analysis of the Tensile Strength of Composite Material from Fiber Bags. Journal of Applied Sciences and Advanced Technology, 2(2), 39-48.

Rahardja, I. B., Rahdiana, N., Mulyadi, D., Al Afghani, A., & Ramadhan, A. I. (2020). Analisis Pengaruh Radius Bending Pada Proses Bending Menggunakan Pelat Spcc-Sd Terhadap Perubahan Struktur Mikro. Jurnal Teknik Mesin Mechanical Xplore, 1(1), 1-10.

WANG, C. Y., WANG, T. T., & HAN, Y. C. (2008). Research on stamping performance of tailor welded blanks [J]. Forging & Stamping Technology, 4.

Halim, I., Omar, A. R., & Saad, N. H. (2005, June). Investigation Of Work-Related Musculoskeletal Disorders In Malaysian Metal Stamping Industry Using Rula Method. In Paper presented at 8th Conference & Exhibition on Occupational Safety and Health (COSH) (Vol. 28, No. 29).

ZHENG, J. Q., JIANG, X. H., WANG, Y. L., & LI, Z. G. (2005). Research of the CAPP System for the Stamping Process for Auto Body Metal Sheet Parts [J]. Die & Mould Industry, 3.

Othman, N. L. A., Hussain, N. S., Ibrahim, D., & Yaacob, Y. (2019, November). Safety and risk evaluation implementation at sheet metal stamping company using HIRARC model. In IOP Conference Series: Materials Science and Engineering (Vol. 670, No. 1, p. 012070). IOP Publishing.

Ribeiro, I., Peças, P., Silva, A., & Henriques, E. (2008). Life cycle engineering methodology applied to material selection, a fender case study. Journal of Cleaner Production, 16(17), 1887-1899.

Diniardi, E., Setiawan, B., & Ramadhan, A. I. (2019). Fatigue Analysis Aluminium 6063-TF on the Rotary Bending Testing Machine. Journal of Applied Sciences and Advanced Technology, 2(1), 7-12.




DOI: https://doi.org/10.24853/jasat.3.3.75-80

Refbacks

  • There are currently no refbacks.


Copyright of Journal of Applied Sciences and Advanced Technology (JASAT)

 

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License

Journal Statistic

Powered by Puskom-UMJ